Industrial & Construction Solutions

PRODUCT DESCRIPTIONFasto 555 is a low viscosity high strength very fast curing specially formulated modified Ethyl Cyanoacrylate adhesive. Fasto 555 is suitable for bonding substrate like rubber, plastics, etc. Fasto 555 offer very high speed curing for substrate like rubber & plastics.TYPICAL APPLICATIONSFasto 555 is formulated for the bonding of plastics, rubbers, leather & other common substrates.PROPERTIES OF UNCURED MATERIALChemical type EthylAppearance ClearSpecific Gravity 1.03Viscosity cPs1range 3 -5Tensile Strength2 (N/mm2) 12Fixture Time (secs) 2 - 3Full Cure (hours) 24Shelf Life @ 22°C (months) 6Max Gap Fill (mm) 0.10Operating Temperature -30 to +80Range (°C)1 ISO 3104/31052 ISO 6922TYPICAL CURING PERFORMANCETypical Speed:Steel/steel <8 -10 secondsABS/ABS <6 secondsRubber/Rubber <5 secondsCure speed vs. environmental conditionsCyanoacrylate adhesives require surface moisture on the substrates in order to initiate the curing mechanism. The speed of cure is reduced in low humidity conditions. Low temperatures will also reduce cure speed. All figures relating to cure speed are tested at 21°CCure speed vs. bond gapFasto 555 give best results on close fitting parts. The product should be applied in a very thin line in order to ensure rapid polymerisation and a strong bond. Excessive bond gaps will result in slower cure speeds. Fasto Cyanoacrylate Activators may be used to greatly increase cure speedsCure speed vs. SubstrateThe speed of cure of Fasto 555 varies according to the substrates to be bonded. Acidic surfaces such as paper and leather will have longer cure times than most plastics and rubbers. Some plastics with very low surface energies, such as polyethylene, polypropylene and Teflon® require the use of suitable Fasto Cynoacrylate Activator.TYPICAL ENVIRONMENTAL RESISTANCEHot strengthFasto 555 adhesive is suitable for use at temperatures up to 80°C. At 80°C the bond will be approximately 65% of the strength at 21°C. The bond strength at 100°C is approximately 40% of full strength at 21°C.Chemical / Solvent ResistanceFasto 555 exhibit excellent chemical resistance to most oils and solvents including motor oil, leaded petrol. Fasto 555 is not resistant to high levels of moisture or humidity over time.DIRECTIONS FOR USEBond speed is very fast so ensure that parts are properly aligned before bonding. Ensure parts are clean, dry and free from oil and grease. Product is normally hand applied from the bottle. Apply sparingly to one surface and press parts firmly together until handling strength is achieved. As a general rule, as little Cyanoacrylate as possible should be used – over application will result in slow cure speed and lower bond strength. Please contact your Fasto representative for further advice on dispensing solutions.GENERAL INFORMATIONFor safe handling of this product consult the Material Safety Data Sheet.Removal Of Cured CyanoacrylateCured Cyanoacrylate may be removed from most substrates, and parts disassembled, with Fasto CA Debonder. It is not possible to fully remove Cyanoacrylate from fabrics.StorageStore in a cool area and out of direct sunlight. Refrigeration to 5° C gives optimum storage stability.PackagingBottles: 20gAvailable in bulk for use with dispensing systems.DATA RANGESThe data contained in this data sheet may be reported as typical value and/or range. Values are based on actual test data and are verified on a regular basis.

Additional Information:

• Delivery Time: Immediate
• Packaging Details: 20gm

777S is a very low viscosity fast cure one component cyanoacrylate designed for general purpose bonding of substrates viz., Metal, various plastics and Rubbers at room temperature. 

Additional Information:

• Delivery Time: immediate
• Packaging Details: 20Gm

PRODUCT DESCRIPTIONSicomet 100 is a fast curing medium-viscosity ethylcyanoacrylatefor bonding a wide range of materials including plastics and rubbers.Sicomet 100 provides the following product characteristics:Chemistry Type Ethyl cyanoacrylateAppearance : (uncured)Colourless liquidComponents One part – requires no mixingViscosity : Medium-lowCure : Surface moistureApplication : Instant BondingKey Substrates : Plastics, rubbers (incl. foam), metals and fabricsFEATURES & BENEFITS Excellent adhesion to rubbers and plastics Fast Cure Easy to apply and dispense  No mixing requiredProperties of uncured material     Typical valueSpecific Gravity :                       @ 25ºC 1.05 – 1.10Viscosity :                               @ 25ºC 140 – 220mPa.sFlash Point (TCC) :                        See MSDSTYPICAL CURING PERFORMANCECuring of Sicomet 100 is initiated by surface moistureand handling strength is achieved rapidly between closefitting parts. Fixture time is dependent on the substratematerial and gap. Curing continues for at least 24 hoursbefore full strength and chemical/solvent resistance isdeveloped.

Additional Information:

• Delivery Time: Immediate
• Packaging Details: 20Gm

Loctite 495 Is A Transparent, Colourless, Low-Viscosity, General Purpose Instant Adhesive Offering Quick Bonding. It Can To Bond A Wide Range Of Materials, Including Plastics, Rubbers And Metals. Also, Suitable For Polyolefins If Used With Primers.

• General Purpose

• Low-Viscosity

• Bonds Plastics, Rubbers & Metals

Additional Information:

• Delivery Time: immediate
• Packaging Details: 20Gm

LOCTITE® 415™ is a general purpose adhesive and is particularly suited to bonding of metal substrates. Mil-A-46050C LOCTITE® 415™ is tested to the lot requirements of Military Specification Mil-A-46050C. Note: This is a regional approval. Please contact your local Technical Service Center for more information and clarification.

• High viscocity adhesive offering maximum adhesion to metals.
• Ideal for bonding small metal parts for general maintenance.

 

Additional Information:

• Delivery Time: immediate
• Packaging Details: 20gm

Fasto CA01 is a low-medium viscosity, fast curing, very high strength instant adhesive, specially formulated for bonding plastics. Fasto CA01 is suitable for bonding a very wide range of materials, including some porous ones, where very fast cure speed is required.Fasto CA01 is formulated for the bonding of plastics, rubbers, metals and other common substrates. It is recommended for use on close-fitting parts and smooth & even surfaces. PROPERTIES OF UN

Additional Information:

• Delivery Time: immediate
• Packaging Details: 20GM

With a precise understanding of the relevant industry, we introduce ourselves as the leading manufacturer, exporter and supplier of Cyanoacrylate Adhesive. This adhesive is processed by utilizing quality approved chemical compound and latest technology in accordance with industry set guidelines. Our offered adhesive is tested on different quality parameters by our quality parameters. The entire range of adhesive is made available in various packaging options as per the requirements of our clients.

Fasto CA15 is a very high viscosity high strength specially formulated modified Ethyl Cyanoacrylate adhesive for bonding metals. Fasto CA15 is also suitable for bonding wide range of substrates like rubbers, plastics, composites, etc.

Features:

• High performance
• Metal bonding
• High adhesiveness
• Excellent bonding strength
• Non toxic smell

Additional Information:

• Delivery Time: Immedite
• Packaging Details: 20GM

With the support of our experts and sophisticated in-house facilities, we have been able to offer an array of Cyanoacrylate Adhesive. Processed of world class chemical compounds and latest technology under the supervision of highly skilled professionals, this adhesive is highly demanded in the market. Our offered adhesive can also be customized in order to fulfill the vast demands of the clients. Further, our offered adhesive can be availed by our clients at affordable prices.

Fasto CA95 is a low-medium viscosity high strength specially formulated modified Ethyl Cyanoacrylate adhesive. Fasto CA95 is suitable for bonding a very wide range of materials, including some porous ones, where very fast cure speed is required.

Features:

• High performance
• High strength
• Fast curing
• High gap filling capability
• High temperature resistance

Additional Information:

• Delivery Time: immediate
• Packaging Details: 20gm

LOCTITE® Product 401 is a low viscosity, fast curing, single component cyanoacrylate adhesive. It is specifically formulated for difficult to bond substrates. This product is less dependent on surface moisture for cure speed than other standard CA grades. TYPICAL APPLICATIONS Rapid bonding of a wide range of metal, plastic or elastomeric materials, particularly suited for bonding porous or absorbent materials such as wood, paper, leather or fabric.Rapid bonding of a wide range of metal, plastic or elastomeric materials, particularly suited for bonding porous or absorbent materials such as wood, paper, leather or fabric.

Additional Information:

• Delivery Time: immediate
• Packaging Details: 20gm only

My-T-Glue® is a very low viscosity fast cure one component cyanoacrylate designed for general purpose bonding of substrates viz., Metal, various plastics and Rubbers at room temperature. 

Additional Information:

• Delivery Time: Immediate
• Packaging Details: 20gm